Surface burnishing is usually a complex procedure that requires time and enough money to get favorable results.Different companies have seen to it that they outline steps that clients should read to know exactly what they need to know about Florida Commercial Polished Concrete during the varnishing. Because if a surface is not smooth, it tends to have a thin layer that must be removed.
The machine uses rough diamonds that are made of metal. If the aggregate present in the floor has been exposed, the burnish from the first pour has to be removed too. This process is a bit complex than many people think thus it requires technicians that are both qualified and experienced.
The initial stage is to grind the surface. However, the technicians must first perform a test to check the hardness of the floor so that they can select the best diamond tools to use. This is an important step that has to be done. Then, the diamond tooling is put in the grinder and grinding is commenced. Any repairs should be done during this stage.
When grinding has been finished, the application of stains followed by densifier is made. When the top layer is removed, the floor becomes weak thus applying the densifier makes it hard again. It is important to note that the stain should be applied first and left to dry before applying the densifier. The slab should left wet for approximately 20-30 minutes before proceeding to the next step.
After a few minutes, honing is done on floors after making sure that the densifier has dried. Diamond pads that have grit close to 500 are used for this process. After some minutes, one can observe a glossy mirror-like look on the surface. However, it can take longer before the glossiness starts to appear hence making the technicians work for longer hours than usual.
Varnishing the slab is now done using more diamond pads with higher grits to make the floor smooth. The slab is made smooth depending on how the customer has requested. Some customers would like the floors to have a gleaming mirror-like appearance while others prefer floors that have moderate shining that will not be too shiny.
Diamond pads that have been designed for different degrees of glossiness are used on these floors. This is the final stage thus it is the most important. If the varnishing is not done in a standard way, the results will not be appealing thus a lot of care should be taken during this stage. For this reason, it is important to ensure that the technicians are qualified.
The steps should be followed closely so that the results can be appealing. It is however obvious that the steps are different in each company hence make sure that you read and understand the guidelines that you are provided with by your technicians. With this, it will be easier to understand what the technicians will be doing.
The machine uses rough diamonds that are made of metal. If the aggregate present in the floor has been exposed, the burnish from the first pour has to be removed too. This process is a bit complex than many people think thus it requires technicians that are both qualified and experienced.
The initial stage is to grind the surface. However, the technicians must first perform a test to check the hardness of the floor so that they can select the best diamond tools to use. This is an important step that has to be done. Then, the diamond tooling is put in the grinder and grinding is commenced. Any repairs should be done during this stage.
When grinding has been finished, the application of stains followed by densifier is made. When the top layer is removed, the floor becomes weak thus applying the densifier makes it hard again. It is important to note that the stain should be applied first and left to dry before applying the densifier. The slab should left wet for approximately 20-30 minutes before proceeding to the next step.
After a few minutes, honing is done on floors after making sure that the densifier has dried. Diamond pads that have grit close to 500 are used for this process. After some minutes, one can observe a glossy mirror-like look on the surface. However, it can take longer before the glossiness starts to appear hence making the technicians work for longer hours than usual.
Varnishing the slab is now done using more diamond pads with higher grits to make the floor smooth. The slab is made smooth depending on how the customer has requested. Some customers would like the floors to have a gleaming mirror-like appearance while others prefer floors that have moderate shining that will not be too shiny.
Diamond pads that have been designed for different degrees of glossiness are used on these floors. This is the final stage thus it is the most important. If the varnishing is not done in a standard way, the results will not be appealing thus a lot of care should be taken during this stage. For this reason, it is important to ensure that the technicians are qualified.
The steps should be followed closely so that the results can be appealing. It is however obvious that the steps are different in each company hence make sure that you read and understand the guidelines that you are provided with by your technicians. With this, it will be easier to understand what the technicians will be doing.
About the Author:
You can find details about the benefits you get when you install Florida commercial polished concrete floors at http://www.concretereflections.com right now.
ليست هناك تعليقات:
إرسال تعليق